LIGHT OUTPUT
Not sure which LEDEX curing light fits your practice?
LEDEX™ DENTAL CURING LIGHTS
Six curing lights.
One right fit for your chair.
From a lightweight everyday light to 3,200 mW/cm² Plasma output, broadband 390–480 nm LEDs and built‑in caries detection — compare the LEDEX range and find the model that matches the way you work.
BROADBAND
Broadband 390–480 nm for PPD and TPO photoinitiators
ORTHO-READY
Ortho curing cycles on four of six models
FIND YOUR LIGHT
Start with how you work, not with the spec sheet
Every LEDEX light uses a genuine optical‑fibre light guide, overheat protection, last‑setting memory and auto sleep. What changes is power, wavelength, modes and charging — pick the card that sounds like your practice.
Everyday composites
WL-070
Lightweight and simple to run: two buttons, a cordless / corded combo design and seven colours to choose from.
1,000 mW/cm²
Max radiant intensity
- 440–480 nm, peak 460 nm · 5 W LED
- Standard and Ramp modes, 10–40 s
- About 40 min per charge (240 × 10 s)
- 120 g with battery and Ø8 mm light guide
Cordless with output check
WL-070+
Set it on the wireless inductive charging stand — no cable, no pogo pins — and check output on the built‑in intensity indicator.
1,200 mW/cm²
Max radiant intensity
- 440–480 nm · 5 W LED
- Standard and Ramp modes
- Wireless charging stand + built‑in radiometer
- About 40 min per charge · 120 g · Ø8 mm guide
Orthodontic bonding
WL-070+ ORTHO
Ortho curing in just 4 seconds: preset 4, 5 or 6‑second cycles that count down bracket by bracket, group by group.
1,400 mW/cm²
Ortho mode output
- Ortho mode 4 / 5 / 6 s at 1,400 mW/cm²
- Standard mode 10 / 20 / 30 s at 1,000 mW/cm²
- Wireless charging stand + built‑in radiometer
- About 40 min per charge · 120 g · Ø8 mm guide
Full power, every mode
WL-090
Seven curing modes from 600 mW/cm² Low to 3,200 mW/cm² Plasma — cures composite over 2 mm in 1 second.
3,200 mW/cm²
Plasma mode
- 440–480 nm, peak 460 nm · 10 W LEDs
- Low, Ramp, Standard, High, Fast Ortho, Turbo, Plasma
- About 120 min per charge (720 × 10 s Standard)
- 180 g · Ø11 > 8 mm light guide · built‑in radiometer
Cure and inspect
WL-090+
Broadband 390–480 nm LEDs for PPD and TPO photoinitiators, plus Caries and Plaque inspection modes in the same handpiece.
2,400 mW/cm²
Turbo mode
- 390–480 nm, peaks 405 / 460 nm · 10 W LEDs
- 8 modes incl. Fast Ortho, Caries and Plaque inspect
- About 120 min per charge (720 × 10 s Standard)
- 180 g · Ø11 > 8 mm and Ø11 > 5 mm guides
Fastest cure, lighter body
WL-120
2 mm of composite in 1 second at 3,200 mW/cm², broadband LEDs, ortho cycles in every curing mode and a white‑light inspection mode.
3,200 mW/cm²
Plasma mode
- 390–480 nm, peaks 405 / 460 nm · 10 W LED
- Low, Ramp, Standard, High, Turbo, Plasma, White
- About 90 min per charge (540 × 10 s Standard)
- 153 g · Ø11 > 8 mm guide · radiometer for 5 / 8 / 11 mm
COMPARE
All six LEDEX models, side by side
Output, wavelength, battery and every curing and inspection mode in one table. On a phone, swipe the table sideways to see all models.
WL-070
WL-070+
WL-070+ ORTHO
WL-090
WL-090+
WL-120
Best for
Everyday composites
Cordless + output check
Orthodontic bonding
Full power, every mode
Cure and inspect
Fastest cure, lighter body
Light source
5 W LED
5 W LED
5 W LED
10 W LED
10 W broadband LED
10 W broadband LED
Wavelength
440–480 nm
peak 460 nm
440–480 nm
peak 460 nm
440–480 nm
peak 460 nm
440–480 nm
peak 460 nm
390–480 nm
peaks 405 / 460 nm
390–480 nm
peaks 405 / 460 nm
Max radiant intensity
1,000 mW/cm²
1,200 mW/cm²
1,400 mW/cm²
3,200 mW/cm²
2,400 mW/cm²
3,200 mW/cm²
Wireless charging
—
✓
✓
✓
✓
✓
Built-in radiometer
—
✓
✓
✓
✓
✓
Battery use time
~40 min
(240 × 10 s)
~40 min
(240 × 10 s)
~40 min
(240 × 10 s)
~120 min
(720 × 10 s)
~120 min
(720 × 10 s)
~90 min
(540 × 10 s)
Battery
3.6 V, 800 mAh
3.6 V, 800 mAh
3.6 V, 800 mAh
3.6 V, 3,350 mAh
3.6 V, 3,350 mAh
3.6 V, 1,940 mAh
Weight
120 g
120 g
120 g
180 g
180 g
153 g
Light guide
Ø8 mm
Ø8 mm
Ø8 mm
Ø11 > 8 mm
Ø11 > 8 mm
Ø11 > 5 mm
Ø11 > 8 mm
Curing and inspection modes
Standard
✓
✓
✓
✓
✓
✓
Ramp
✓
✓
✓
✓
✓
✓
Ortho
—
—
✓
✓
✓
✓
Low
—
—
—
✓
✓
✓
High
—
—
—
✓
✓
✓
Turbo
—
—
—
✓
✓
✓
Plasma
—
—
—
✓
—
✓
Caries inspect
—
—
—
—
✓
—
Plaque inspect
—
—
—
—
✓
—
White light
—
—
—
—
—
✓
Battery use time is approximate and depends on battery age, mode and ambient temperature. Radiant intensity tolerance ±10%. Specifications subject to change.
CURING MODES
What each mode is for
Factory settings for the WL-090 series and WL-120. Each model offers the modes ticked in the comparison table above.
WL-070 and WL-070+ run Standard and Ramp at up to 1,000 and 1,200 mW/cm². WL-070+ ORTHO adds a 1,400 mW/cm² Ortho mode with 4, 5 or 6‑second cycles.
Mode
Output
Time settings
Recommended for
Low
600 mW/cm²
10, 20, 30, 40 s
Tooth and composite resin
Ramp
1,000 mW/cm²
5–40 s, in 5 s steps
Wide areas of composite, to limit shrinkage
Standard
1,000 mW/cm²
5–40 s, in 5 s steps
Most cases
High
1,800 mW/cm²
2, 4, 6, 8, 10 s
Orthodontic or paediatric dentistry
Fast Ortho
1,800 mW/cm²
3, 4, 5 s, repeated 10 times
Orthodontic bonding cycles (WL-090, WL-090+)
Turbo
2,400 mW/cm²
2, 3, 4, 5 s
Dental cement, porcelain veneers, fibre posts
Plasma
3,200 mW/cm²
1, 2, 3, 4 s
Dental cement, porcelain veneers, fibre posts (WL-090, WL-120)
Caries inspect
350 mW/cm²
30 s
Caries inspection (WL-090+)
Plaque inspect
250 mW/cm²
30 s
Plaque inspection (WL-090+)
White light
H 11,100 lux
L 3,500 lux
5 min
Visualising root canal orifices, crown and root fractures and caries (WL-120)
IN EVERY LEDEX
Built the same way, whichever model you choose
Genuine optical‑fibre light guide
Real optical fibre, not acrylic, minimises light loss from source to tip for the highest possible intensity at the light guide tip.
Overheat protection
A high‑efficiency heat sink, thermal protection circuit and safety mode keep the light from overheating.
Remembers your last setting
The mode and curing time you used last are memorised automatically, so you pick up where you left off.
Automatic sleep
The handpiece sleeps when it is not in use, saving battery and extending use time between charges.
Frequently asked questions
Which LEDEX is best for orthodontic bonding?
WL-070+ ORTHO is built for it, with a 1,400 mW/cm² Ortho mode and 4, 5 or 6‑second cycles. WL-090 and WL-090+ add a Fast Ortho mode (1,800 mW/cm², 3–5 s repeated 10 times), and on WL-120 the ortho cycles can be set in every curing mode.
Do I need a broadband 390–480 nm light?
WL-090+ and WL-120 add a 405 nm peak alongside 460 nm, making them especially suited to materials using phenyl propanedione (PPD) or Lucirin TPO photoinitiators. Check your material's instructions for its recommended curing wavelength.
How do I check the light output?
Every model except WL-070 has a built‑in radiometer. Hold the light guide on the sensor and switch the light on to read the intensity. If Standard mode reads below 700 mW/cm², contact your dealer.
Which light guides fit which model?
The WL-070 series ships with a Ø8 mm guide; WL-090, WL-090+ and WL-120 with a Ø11 > 8 mm guide, and a Ø11 > 5 mm guide is listed for WL-090+. Tapered, shortened and straight optical‑fibre guides are available — ask your dealer which fit your model.
What colours are available?
WL-070 comes in white, black, orange, blue, green, pink and yellow. WL-070+ and WL-070+ ORTHO come in white, black, orange, blue, green, red and purple, with a matching charging stand.
Can the battery be replaced?
Yes. The Li‑ion batteries are consumables and are sold as spare parts for every model. Replace the battery when use time drops noticeably or high‑output modes such as Turbo and Plasma become hard to run.
How do I prevent cross‑infection?
Cover the handpiece with a disposable sleeve for every patient and discard it afterwards — sleeves must not be reused. Sleeves are available for the WL-070 series, for WL-090 / WL-090+ / WL-120, and for the Ø8 mm light guide.
